🚗Best car tint film manufacturers for 2020

The blinding sun will cause many problems for the motorist. Starting from the inconvenience experienced in a traffic jam, the rise in temperature in the cabin and ending with a negative impact on the inner lining. Quite often, because of the blinding sun, the driver does not have time to brake in time, or go away from the obstacle that has arisen.

Tinting film relieves the driver of this kind of inconvenience.

What tinting is allowed according to GOST

Those who have thought about such protection need to study the legal side of the issue. Knowledge of all legislative aspects will allow making the right choice. There are certain norms, the violation of which will entail financial liability.

In 2020, the requirements for the amount of light transmitted by tinted glass were tightened. According to the new standards, there are 2 categories of glass in a car:

• for front view
• rear view glass.

The new legislation establishes the following standards for light transmission:

• windshield - 75%;
• lateral front - 70%;
• there is no restriction on the rear, subject to the presence of the appropriate side mirrors;
• in the upper part of the windshield, a strip of any degree of shading is allowed if the width does not exceed 140 mm.

A taumeter is used to check the degree of darkness. The procedure is regulated by a set of rules and recommendations.

1. Carrying out strictly at stationary posts of service workers.
2. If it is raining or the humidity level is 45 - 80%, the test is not possible.
3. The glass is clean and dry.
4. Measurements are made at 3 arbitrary points, each glass.
5. Atmospheric pressure level 649 - 750 mm.
6. The police officer must have a corresponding mark on the certificate.
7. The device must have certificates and seals.
8. Measurement is possible at temperatures from +15 to + 25 C.

What does it consist of

The main chemical elements are polymers and dyes. The components may differ depending on the intended purpose, type, quality and manufacturer.

A product consists of several layers, the quantity is determined by the type of product. The popular metallized film consists of:

1. Elastic polymer base (basic component of any tinting).
2. Dyes (set a certain tone and darken).
3. Metallized polyester film with metal spraying (reflects infrared rays).
4. UV absorbers (protect the driver and passengers from their negative effects).
5. Adhesive layer (prevents delamination of the structure).
6. Contact surface (use acrylic resin, which is necessary for fixing).
7. Anti-abrasive coating (protects against scratches and other damage).

In other types, certain components may be absent. An example is dyed films that lack a metallized element.

What are

1. Painted. A budget option. The composition includes pigments that give the desired color. Its amount has a direct effect on light transmission. They do not glare, nothing interferes with the proper operation of radio devices.But it quickly deteriorates and is practically not resistant to negative environmental influences. Now they are practically not used.
2. Metallized. The main feature is in the metal layer applied on top of the painted one. In most cases, it is aluminum. The layer itself can be inner or outer. After pasting, the glass acquires the appropriate gloss.
3. Spatter. Its properties are similar to metallized ones, the main difference is that the metal was applied by ionization. With its help, it is allowed to apply any chemical substance to the polymer layer and, as a result, a uniform coating can be obtained. The peculiarity of the production "presented" the maximum durability. The belief in quality is so great that some of the spatter film companies offer a lifetime warranty. Such coatings have an excellent appearance.
4. Infinity. The outer side is covered with a metallized layer. This increased the reflective properties by up to 70%. The acquired mirror shine hindered the spread and popularization, since such an effect is prohibited by law.
5. Combined. They have incorporated the qualities of colored and metallized films. In them, one tone smoothly passes into another. The effect is achieved by changing the intensity of the deposition of metal particles. The upper dark side will protect from the sun, while the lower light side will keep good visibility on the road. This product is popular among connoisseurs of visual tuning.
6. Athermal (energy saving). Innovative development. With it, you can forget about the overheating of the cabin. Blocks up to 90% of the sun's rays. The nano ceramic coating with a graphite layer will reliably protect the driver and passengers from the negative effects of ultraviolet rays and retain perfect visibility even in adverse weather conditions. It should be understood that it does not darken, in other words, everything that happens in the cabin will be visible to passers-by. The positive side of this moment is that the driver will not have any problems with the law. The only thing to pay attention to is the LA series films, they have a blue tint. It negatively affects the eyes. Purchase of ATR with neutral colors is preferred.
7. Chameleon. A type of athermal film with a violet shade. After application, the glass shimmers beautifully in the sun. A distinctive feature is the change in the amount of transmitted light depending on the intensity of illumination. In this regard, problems may arise with determining the degree of darkness, the results of measuring the toning may be different depending on the degree of illumination of the room.
8. Carbon. Elite product. Not common. Not everyone can afford to buy. This is due to the peculiarities of manufacturing. The film is placed under vacuum and a graphite layer is sprayed onto it. The resulting product has properties similar to metallized, but completely devoid of its weaknesses. Throughout the entire service, does not lose color and reflects over 50% of infrared rays, does not create glare.

Depending on the intended use, there are:

1. Sunscreens. Protect the driver from the negative effects of ultraviolet radiation.
2. Shock Resistant Armor Car Glass. If damaged, it becomes covered with a web of cracks and remains in place without crumbling.
3. Decorative. Allows you to stand out on the road.

Do I need to tint glass

The question has no definite answer. Much depends on the driver and his preferences. Those who asked this question are encouraged to examine the strengths and weaknesses of the process.

Advantages:

Disadvantages:

How to choose

The range is so large that it is easy to get lost not only for a beginner, but also for a seasoned car enthusiast. The error will cause various kinds of inconvenience while driving. Experts have developed recommendations to avoid such problems. Before buying, pay attention to:

1. Bandwidth. It characterizes the amount of visible light that tinted glass is able to transmit. The minimum rate is 5%. A comfortable ride is possible at 15%. The optimal value at which what is happening in the cabin will be practically invisible. With her, driving at night will not cause problems. 35% is practically not used by motorists. This is due to the fact that such a salon is clearly visible from the outside. The choice of people with poor eyesight. 35% and below are glued to the windshield.
2. Anti-scratch coating. It is represented by a silicone layer on the product. Without it, scratches will occur during gluing and smoothing with a spatula. When lowering the glass, white scratches are formed, as grains of sand get stuck between the tinting and the felt. This is prevented by the silicone coating. Manufacturers producing goods in the premium segment create such a high-quality silicone coating that even touching the butt of a cigarette is not capable of causing harm. On the packaging, the silicone layer is shown with the SRC mark.
3. How quickly it burns out High-quality ordinary film can last for 2 - 3 years. Metallized and American (persistent dyes) are used from 3 to 5. Spatter and ceramic serve for 7 years.
4. Molding. The need for molding is encountered when pasting a single piece of glass, bending in two planes. To do this, use an industrial hair dryer in the second mode of operation (temperature 600 - 700 degrees). A quality product includes polyester, which stretches when heated. Polyethylene is not capable of this.
5. Clear view through the film. On low-quality products, the dye is unevenly distributed and this is clearly visible by ripples on the surface. They cause fatigue and decreased concentration.

The best manufacturers producing the most inexpensive tint films

MTF Light

Among the many American and Asian companies engaged in the development of films for car tinting, there was a place for domestic developers. The products cover all categories of enthusiasts of this kind of tuning and provide a spacious range of products. The quality is not inferior to foreign counterparts. The pleasant price stirs up the interest of domestic car owners. The latter is confirmed by employees of specialized service stations.

Advantages:

Disadvantages:

SunControl

The company, originally from India, quickly gained the credibility and recognition of domestic motorists. This became possible due to the high level of protection against ultraviolet radiation (99%), low throughput. electromagnetic rays and high-quality sound insulation. Athermal films, due to their high heat-insulating qualities, can save up to 3% of fuel on the use of an air conditioner.

Advantages:

Disadvantages:

Nova bright

One of the old-timers in the market. She settled in Russia since 2002. During this time, the status of a reliable company that can be trusted has been consolidated. They produce only high quality and reliable accessories. With them, you can highlight your four-wheeled friend.

Tinting films block up to 98% of the sun's rays and prevent interior fading. In this case, the view from the inside does not deteriorate, since the luminous flux is limited only in one direction.

Advantages:

Disadvantages:

The best manufacturers of tint films in the middle price segment

Global

The ambitious newcomer in a relatively short period of time was able to win the hearts of motorists and establish himself on the positive side. This was also favorably influenced by the unique characteristics of the products. At the plant, raw materials go through a full cycle, from preparation to packaging of finished products. With Global films, you can forget about the burnout of the interior and the negative effect of ultraviolet rays on the body.

Advantages:

Disadvantages:

Armolan

It occupies a leading position in the car tint films market. A distinctive feature that sets it apart from many others is the high requirements for the product. The bar set by Armolan was successfully maintained. The products cover all market segments (from budget to premium). The correct approach to pricing resonated with domestic motorists.

Advantages:

Disadvantages:

3M

Quality and reliability are the two pillars that have allowed the American company to take a leading position in the market. They are so confident in their products that they even provide a warranty. The film is based on nano-carbon polyester, without metallic impurities. The latter eliminates interference in the operation of electrical equipment. It should be noted that the film has good UV protection properties.

Advantages:

Disadvantages:

The best manufacturers of premium tint films

Shadow guard

The company, originally from South Korea, sells black and athermal films. PHP CHAORACAL series is highly popular - a unique combination of metal and ceramics. The product lends itself to forming.

Advantages:

Disadvantages:

SunTek

One of the main competitors of Llumar. In many automotive forums, discussions about who is better are not fading away. Users note that after installation, the temperature in the cabin significantly decreases, and the efficiency of the climate control increases. The material enhances the strength of the glass. The coating that prevents scratches and chips will retain its original appearance for a long time.

Advantages:

Disadvantages:

LLumar

The undisputed market leader. Eastman Chemical Company was founded back in 1920. The Llumar trademark was registered after the development of an innovative technology for producing colored polyethylene terephthalate. A wide range of products and tight control have helped the company gain recognition. The product does not fade and lasts for 6 years. The addition of metal particles increased the strength.

Advantages:

Disadvantages:

The top lists the best firms in a specific market segment. Having stopped the choice on one of them, you can not worry that the goods will come of inadequate quality. They are the standard of excellence, and this is confirmed by numerous positive reviews from those who have already used the products.